Aluminum horizontal blinds 16/25 mm
Aluminum horizontal blinds with 16/25 mm strip are designed to close small window openings.
Why do customers choose aluminum horizontal blinds?
• Blade coloring resistant to abrasion and fading, wet sweeping possibility
• Reliable control mechanisms and durable steel rails
• Wide color palette, various decorative coatings and trendy textures
![рис1.jpg рис1.jpg](/upload/medialibrary/b9a/b9aa153cf67575d3a0249404d198f68c.jpg)
Front view |
Вид спереди |
Side view |
Вид сбоку |
product height |
высота изделия |
Amigo horizontal aluminum blinds 16/25 mm are recommended to be installed
outside/inside openings.
• These are loose-hanging models of rectangular, round and trapezoid shapes (ref. to section "Additionally")
• The aluminum blades are pulled up and down by means of a cord; the blades are tilted by means of a clear plastic wand. The control may be either divided or combined. The control may also be implemented using electric drive. • Upon request: decorative valance made of two 25 mm blades.
The products with width < 43.5 cm are manufactured with the divided control only.
• Blind sheet may be fixed at any given level
• The allowance for the ready-made product height is: +12 mm (16 mm blades) and +21 mm (25 mm blades)
DIVIDED CONTROL |
РАЗВЕДЕННОЕ УПРАВЛЕНИЕ |
Cord on the right / Wand on the left |
Веревка справа / Прут слева |
Cord on the left / Wand on the right |
Веревка слева / Прут справа |
COMBINED CONTROL |
СОВМЕЩЕННОЕ УПРАВЛЕНИЕ |
Right |
Справа |
Left |
Слева |
16/25 mm limit dimensions:
Blade width, mm |
Width, cm |
Height, cm |
Max. area, sq.m |
Control length*, cm |
|||
Min. |
Max. |
Min. |
Max. |
Min. |
Max. |
||
16 |
25 |
210 |
30 |
300 |
7.0 |
50 |
300 (wand) / unlimited (cord) |
25 |
25 |
285 |
*The tilting wand length is by default 2/3 of the product height.
• Valance. Made of two 25 mm blades of the same color with the fabric sheet.
• Side fixation. On either side of all blades there are steel wires routed through additional openings on both sides that prevent the blade sheet from shaking during draft. The wire at the bottom is attached with a plastic B-type bracket.
Side fixation is a simple and effective solution for the reliable sheet fixation while maintaining all the blind operational features. This model is perfect to be installed on tilt and turn windows and glazed doors. The fixation is made by means of the steel wires routed through the openings in the blinds on both sides and secured with lower fasteners.
• Valance. Made of two 25 mm blades of the same color with the fabric sheet.
• The bottom rail holder is designed to fix the bottom rail. In this case the product may only tilt.
• Valance. Made of two 25 mm blades of the same color with the fabric sheet.
• The bottom rail holder is designed to fix the bottom rail. In this case the product may only tilt.
SPECIAL SHAPES
TRAPEZOIDS AND HALF-TRAPEZOIDS
Trapezoid-shaped blinds are the functional solutions for openings with a small bevelled edge.
Half-trapezoid |
Полутрапеция |
Trapezoid |
Трапеция |
The bevel size is limited with the following dimensions depending of the blinds width:
Bevel limit, B
Model |
16 mm |
25 mm |
Half-trapezoid |
7.5 cm |
12.5 cm |
Trapezoid |
15 cm |
25 cm |
Control:
cord/wand for half-trapezoid are located at the side opposite to the bevel and arbitrary for trapezoid.
Measurements and installation:
Similar to standard model 16/25 mm. Height, width at the bottom and width at the top are measured.
Additional option:
Side fixation for half-trapezoid is possible from the side opposite to the bevel. Side fixation for trapezoid is not provided.
ROUND
Round-shaped horizontal blinds are available with 25 mm aluminum blades only.
Control:
cord/wand are always located separately.
The sheet is lifted to the maximum width point.
Measurements and standard installation:
Round minimum diameter 400 mm.
Round maximum diameter 1000 mm.
A round opening diameter is measured. 1 cm shall be deducted form the opening diameter to get the product diameter.
2 IN 1
If two products are located next to each other, they may be installed on one head rail with individual control for each of them.
Measurements and standard installation:
similar to standard models 16/25 mm. Distance between sheets - 1 cm.
DECORATIVE OPTIONS
Blinds with blades of different color and/or texture. |
Жалюзи с ламелями разного цвета и/ или фактуры. |
The combination of blades with various perforation percentage within one product is 4% and 8% to get the optimal light flux control. |
Сочетание в рамках одного изделия ламелей с разным процентом перфорации – 4% и 8% для оптимального контроля светового потока. |
The combination of perforated and non-perforated strip within one sheet to get the optimal light flux control. |
Сочетание в рамках одного полотна перфорированной и неперфорированной полосы для оптимального контроля светового потока. |
OUTSIDE A WINDOW OPENING |
СНАРУЖИ ОКОННОГО ПРОЕМА |
Measurement recommendations: Product width = opening width + 10 cm Product height = opening height + pack height* |
Рекомендации по замерам: Ширина изделия = ширина проема + 10 см Высота изделия = высота проема + высота пакета* |
Holis bracket 240180-0000 |
Кронштейн Холис 240180-0000 |
Bottom rail holder for bottom fixation 240172-000 |
Держатель нижнего карниза для нижней фиксации 240172-000 |
B-type lower plastic bracket 249181-0000 |
Кронштейн нижний тип В пластмассовый 249181-0000 |
INSIDE A WINDOW OPENING |
ВНУТРИ ОКОННОГО ПРОЕМА |
Measurement recommendations: Product width = opening width - 0.5 cm Product height = opening height - 2 cm |
Рекомендации по замерам: Ширина изделия = ширина проема – 0,5 см Высота изделия = высота проема – 2 см |
Universal bracket 240180-0000 |
Универсальный кронштейн 240180-0000 |
WARNING!! Ensure that the folded product will not prevent window opening. |
ВНИМАНИЕ!! Необходимо убедиться, что изделие в сложенном виде не будет препятствовать открытию окна. |
![рис6.jpg рис6.jpg](/upload/medialibrary/169/1693f701b136f57bdbb764ab65041547.jpg)
Blind height, cm |
Pack height, cm |
|
16 mm |
25 mm |
|
50 |
7.1 |
6.5 |
100 |
8.3 |
7.6 |
150 |
9.5 |
8.8 |
200 |
10.8 |
9.9 |
250 |
12.0 |
11.1 |
300 |
13.2 |
12.2 |
NUMBER OF BRACKETS FOR BRACKETS 16/25 MM
Product width, m |
Number of brackets, pcs. |
0-1.50 |
2 |
1.50-1.80 |
3 |
1.80-2.30 |
4 |
2.30-2.80 |
5 |
2.80—3.20 |
6 |