Aluminum horizontal blinds 50 mm
Horizontal blinds with 50 mm aluminum blade are designed to close medium and large window openings. The wide aluminum strip effectively discloses the selected material texture. The reliable system of mechanisms provide comfort and long-term operation.
Pair of cord on the right / cord on the left |
Пара веревок слева / веревка справа |
Cord on the left / pair of cords on the right |
Верёвка слева / пара веревок справа |
Side view Aluminum 50 mm |
Вид сбоку Алюминий 50 мм |
Side view Plastic 50 mm |
Вид сбоку Пластик 50 мм |
product height |
высота изделия |
The horizontal blinds 50 mm (aluminum, plastic) are a perfect choice for large windows.
These are loose-hanging models or models with side fixation on a 1 mm diameter wire (fixed at the top and at the bottom).
Rectangular or trapezoid models
The aluminum blades are pulled up and down by means of one cord and tilted by means of a pair of cords tilting the blades in various directions.
Blind sheet may be fixed at any given level
The allowance for the ready-made product height is: +44 mm
Measurements of the horizontal blinds 50 mm are similar to those of the blinds 16/25 mm.
The bottom rail may be fixed similar to the standard models of horizontal aluminum blinds 16/25 mm.
The head rail is always closed by the valance from the front.
Blades material |
Width, cm |
Height, cm |
Max. area. sq.m |
Control length |
|||
Min. |
Max. |
Min. |
Max. |
Min. |
Max. |
||
aluminum |
42 |
270 |
40 |
300 |
7.0 |
50 |
Unlimited |
-
The bottom rail holder is designed to fix the bottom rail. In this case the product may only tilt.
-
25 mm wide decorative ladder that closes the blade openings.
Side fixation. On either side of all blades there are steel wires routed through additional openings on both sides that prevent the blade sheet from shaking during draft. The wire at the bottom is attached with a plastic B-type bracket.
Side fixation is a simple and effective solution for the reliable sheet fixation while maintaining all the blind operational features. This model is perfect to be installed on tilt and turn windows and glazed doors. The fixation is made by means of the steel wires routed through the openings in the blinds on both sides and secured with lower fasteners.
SPECIAL SHAPES
TRAPEZOIDS AND HALF-TRAPEZOIDS
Trapezoid-shaped blinds are the functional solutions for openings with a small bevelled edge.
![рис21.jpg рис21.jpg](/upload/medialibrary/42b/42b24ed8026b8d6479f0c6eab0bbcfc7.jpg)
Half-trapezoid |
Полутрапеция |
Trapezoid |
Трапеция |
Control:
The wooden blades are pulled up and down by means of a pull cord and tilted by means of a separate pair of cords. Divided control; standard design - pull is on the left, tilt is on the right.
Measurements and installation:
Similar to standard model 50 mm. Height, width at the bottom and width at the top are measured.
Additional option:
side fixation for half-trapezoid is possible from the side opposite to the bevel.
Side fixation for trapezoid is not provided.
2 IN 1
If two products are located next to each other, they may be installed on one head rail with individual control for each of them.
Measurements and standard installation:
similar to standard models 50 mm. Distance between sheets - 1 cm.
OUTSIDE A WINDOW OPENING |
СНАРУЖИ ОКОННОГО ПРОЕМА |
Measurement recommendations: Product width = opening width + 10 cm Product height = opening height + pack height |
Рекомендации по замерам: Ширина изделия = ширина проема + 10 см Высота изделия = высота проема + высота пакета |
Set of standard brackets - a pair of side brackets (245581) + central bracket (245580) |
Комплект стандартных кронштейнов – пара боковых (245581) + центральный кронштейн (245580) |
INSIDE A WINDOW OPENING |
ВНУТРИ ОКОННОГО ПРОЕМА |
Measurement recommendations: Product width = opening width - 0.5 cm Product height = opening height - 2 cm |
Рекомендации по замерам: Ширина изделия = ширина проема – 0,5 см Высота изделия = высота проема – 2 см |
WARNING! Ensure that the folded product will not prevent window opening (ref. to page 18) |
ВНИМАНИЕ! Необходимо убедиться, что изделие в сложенном виде не будет препятствовать открытию окна (см. стр. 18) |