+7 (495) 787-97-87

Main / Products / Horizontal blinds / Horizontal blinds made of natural materials / Horizontal wooden and bamboo blinds 25 mm

WOOD/BAMBOO 25 MM WOOD/BAMBOO 50 MM WOODGRAIN PVC 50 MM RETRO classic system 50 mm for horizontal blinds made of natural materials

Horizontal wooden and bamboo blinds 25 mm

Description

рис28.jpg

Front view	Вид спереди
Side view	Вид сбоку
product height	высота изделия

Amigo horizontal wooden blinds 25 mm are recommended to be installed outside/inside an opening. These are loose-hanging rectangular or trapezoid models.

decorative wooden or bamboo valance closing the front head rail (33 mm height)

25 mm wide 2.5 mm thick wooden blades or 1.8 mm thick bamboo blades

wooden bottom rail

the wooden blades are pulled up and down by means of a pull cord and tilted by means of a wooden wand. The control may be either divided or combined.

рис30.jpg

DIVIDED CONTROL	РАЗДЕЛЬНОЕ УПРАВЛЕНИЕ
Cord on the left / Wand on the right	Веревка слева/ Прут справа
Cord on the right / Wand on the left	Веревка справа/ Прут слева

COMBINED CONTROL	СОВМЕЩЕННОЕ УПРАВЛЕНИЕ
Right	Справа
Left	Слева

рис29.jpg

Limit dimensions:

Material	Width, cm		Height, cm		Max. area. sq.m	Control length
	Min.	Max.	Min.	Max.		Min.	Max.
wood	33	210	40	300	3.6	30	wand - 150 cord - unlimited
bamboo	33	178			3.3

Three dimension types of the tilting wand are used (within the product height range):

90 cm (control length < 105 cm)

120 cm (control length 105-135 cm)

150 cm (control length >136 cm)

Options

Angle valance. Closes the head rail on both ends.

Side fixation. Blind sheet fixation on both sides using steel wires routed through the special side openings in the blades.
Does not prevent pulling the blades up/down.
The bottom rail holder is designed to fix the bottom rail. In this case the product may only tilt.
Divided control (if width exceeds 43.5 cm). The cord and wand are located on opposite sides.

Additionaly

SPECIAL SHAPES

TRAPEZOIDS AND HALF-TRAPEZOIDS

Trapezoid-shaped blinds are the functional solutions for openings with a small bevelled edge.

рис7.jpg

Half-trapezoid	Полутрапеция
Trapezoid	Трапеция

The bevel size is limited with the following dimensions depending of the blinds width:

Bevel limit, D

рис34.jpg

Model	Bamboo	Wood
Trapezoid	20 cm	40 cm

Control:
cord/wand are located at the side opposite to the bevel for half-trapezoid and arbitrary for trapezoid.

Measurements and installation:
Similar to standard model 16/25 mm. Height, width at the bottom and width at the top are measured.

Additional option:
Side fixation for half-trapezoid is possible from the side opposite to the bevel. Side fixation for trapezoid is not provided.

ROUND

Round-shaped horizontal blinds are available with 25 mm aluminum blades only.

рис9.jpg

Control:
cord/wand are always located separately. The sheet is lifted to the maximum width point.

Measurements and standard installation:
Round minimum diameter 400 mm. Round maximum diameter 1000 mm. A round opening diameter is measured. 1 cm shall be deducted form the opening diameter to get the product diameter.

2 IN 1

If two products are located next to each other, they may be installed on one head rail with individual control for each of them.

рис10.jpg

Measurements and standard installation:
similar to standard models 25 mm. Distance between sheets - 1 cm.

Measurement and installation

рис33.jpg

OUTSIDE A WINDOW OPENING

СНАРУЖИ ОКОННОГО ПРОЕМА

Measurement recommendations:

Product width = opening width + 10 cm

Product height = opening height + pack height*

Рекомендации по замерам:

Ширина изделия=ширина проема + 10 см

Высота изделия=высота проема + высота пакета*

Set of standard brackets

Комплект стандартных кронштейнов

INSIDE A WINDOW OPENING

ВНУТРИ ОКОННОГО ПРОЕМА

Measurement recommendations:

Product width = opening width - 1 cm

Product height = opening height - 2 cm

Рекомендации по замерам:

Ширина изделия=ширина проема - 1 см

Высота изделия=высота проема – 2 см

Set of standard brackets

Комплект стандартных кронштейнов

ON WINDOW FRAME WITH SIDE FIXATION OPTIONS (with drilling)	НА ОКОННУЮ РАМУ С ОПЦИЕЙ БОКОВАЯ ФИКСАЦИЯ (со сверлением)
Measurement recommendations: Product width = width as per fillet dimension Product height = frame height	Рекомендации оп замерам: Ширина изделия = ширина по габариту штапика Высота изделия = высота рамы
Universal bracket 240180-0000	Универсальный кронштейн 240180-0000
B-type lower plastic bracket 249181-0000	Кронштейн нижний тип В пластмассовый 249181-0000