Special models of Zebra roller blinds (LOUVOLITE) to close openings
COMPOSITIONS
LVT ZEBRA DOUBLE CLASSIC 45 MM
Combination of 2 blind products with the help of an intermediate bracket allows to close large window/door sections and maintain independent control of each blind.
Composition maximum height - 6 m.
Individual control is located outside each product.
The gap between the blind sheets is approximately 1.5 cm.
LVT ZEBRA MONO CLASSIC 2 AND 3 PRODUCTS 45 MM
Combination of 2 blind products with a single control with the help of a connecting bracket allows to close large window sections with width of up to 6 m. Both products are pulled up and down synchronically.
Composition maximum height - 6 m.
Both products shall utilize one name of fabric (different colors are allowed).
The control (chain) is located outside one of the products.
The gap between the blind sheets is approximately 1.5 cm.
1 - product near to which the control is located;
2 - product without control.
Additional option: MONO + DOUBLE
LVT ZEBRA MONO CASSETTE 2 AND 3 PRODUCTS 45 MM
- Easylift
- Chain tensioner
There are no additional designs
LVT DOUBLE CLASSIC 45 MM
|
линия стыка ** |
joint line ** |
|
Ш1 |
W1 |
|
Ш2 |
W2 |
|
В1 |
H1 |
|
В2 |
H2 |
|
см |
cm |
Measurement recommendations (dimensions for request*):
W1, W2 - widths measured from opening edges to a joint line;
H1, H2 - heights for each blind.
Outside an opening:
Blind width 1 = W1 + 8 cm
Blind width 2 = W2 + 8 cm
Blind height 1 = H1 + 10...15 cm
Blind height 2 = H2 + 10...15 cm
Inside an opening:
Width measurements shall be taken minimum in three locations, the minimum ones shall be selected; if reveals are located at an angle, the measurement shall be taken in the location where the composition is assumed to be installed.
Blind width 1 = W1
Blind width 2 = W2
Blind height 1 = H1
Blind height 2 = H2
Attention!
The received dimensions of each product shall be checked as per the table of LVT Classic limit dimensions.
Fabric width 1, 2 = Blind width 1, 2 - 2.8 cm
Gap from the control side - 2.1 cm
Gap from the opposite side - 0.7 cm
* May be revised depending on the opening configuration and space around it.
** To be selected at random (e.g., on an impost), so that there are minimum 1.5 cm on the left or on the right to install a bracket.
FIXTURES
|
Кронштейн промежуточный 45 |
Intermediate bracket 45 |
|
Кронштейн промежуточный 45+ |
Intermediate bracket 45+ |
LVT MONO CLASSIC 2 PRODUCTS 45 MM
|
линия стыка** |
joint line** |
|
Ш1 |
W1 |
|
Ш2 |
W2 |
|
В |
B |
|
см |
cm |
Measurement recommendations (dimensions for request*):
W1, W2 - widths measured from opening edges to a joint line;
H - height of an opening.
Outside an opening:
Blind width 1 = W1 + 8 cm
Blind width 2 = W2 + 8 cm
Blinds height = H + 10...15 cm
Inside an opening:
Width measurements shall be taken minimum in three locations, the minimum ones shall be selected; if reveals are located at an angle, the measurement shall be taken in the location where the composition is assumed to be installed.
Blind width 1 = W1
Blind width 2 = W2
Blinds height = H
Attention!
The received dimensions of each product shall be checked as per the table of LVT Classic limit dimensions
Fig. 125
* May be revised depending on the opening configuration and space around it.
** To be selected at random (e.g., on an impost), so that there are minimum 1.5 cm on the left or on the right to install a bracket.
LVT MONO CLASSIC 3 PRODUCTS 45 MM
|
линия стыка** |
joint line** |
|
Ш1 |
W1 |
|
Ш2 |
W2 |
|
Ш3 |
W3 |
|
В |
B |
|
см |
cm |
Measurement recommendations (dimensions for request*):
W1, W2 - widths measured from opening edges to joint lines;
W3 - width measured between joint lines;
H - height of an opening.
Outside an opening:
Blind width 1 = W1 + 8 cm
Blind width 2 = W2
Blind width 3 = W3 + 8 cm
Blinds height = H + 10...15 cm
Inside an opening
Width measurements shall be taken minimum in three locations, the minimum ones shall be selected; if reveals are located at an angle, the measurement shall be taken in the location where the composition is assumed to be installed.
Blind width 1 = W1
Blind width 2 = W2
Blind width 3 = W3
Blinds height = H
Attention!
The received dimensions of each product shall be checked as per the table of LVT Classic limit dimensions.
Fabric width 1 = Blind width 1 - 2.8 cm
Fabric width 2 = Blind width 2 - 1.0 cm
Fabric width 3 = Blind width 3 - 1.6 cm
LIMIT HEIGHTS OF LVT DOUBLE CLASSIC AND LVT MONO CLASSIC COMPOSITIONS
|
FABRIC WEIGHT G/M2 |
FABRIC TYPE AS PER WEIGHT |
WIDTH OF COMPOSITION WITH 2 PRODUCTS, M (3.0 - 6.0 M) |
WIDTH OF COMPOSITION WITH 3 PRODUCTS, M (6.0 - 7.0 M) |
||||||
|
<3.5 |
<4.0 |
<4.5 |
<5.0 |
<5.5 |
<6.0 |
<6.5 |
<7.0 |
||
|
≤200 |
A |
3.0 |
3.0 |
3.0 |
3.0 |
3.0 |
3.0 |
3.0 |
3.0 |
|
200-320 |
B |
3.0 |
3.0 |
3.0 |
3.0 |
3.0 |
2.0 |
2.0 |
1.5 |
|
≥320 |
C |
2.75 |
2.5 |
2.0 |
2.0 |
2.0 |
1.5 |
1.5 |
1.5 |
* May be revised depending on the opening configuration and space around it.
** To be selected at random (e.g., on an impost), so that there are minimum 1.5 cm on the left or on the right to install brackets.
ZEBRA DIAMOND 1608 LIGHT GRAY, 280 CM
ZEBRA DIAMOND 2261 LIGHT BEIGE, 280 CM
ZEBRA DIAMOND 1852 GRAY, 280 CM
ZEBRA STONE BIO 1854 GRAPHITE, 280 CM
ZEBRA STONE BIO 1608 LIGHT GRAY, 280 CM
ZEBRA STONE BIO 2406 BEIGE, 280 CM
ZEBRA STONE BIO 2259 MAGNOLIA, 280 CM
ZEBRA STONE BIO 2870 BROWN, 280 CM
ZEBRA GLORIA BIO BO 0225 WHITE, 280 CM
ZEBRA GLORIA BIO BO 1608 LIGHT GRAY, 280 CM
ZEBRA GLORIA BIO BO 2259 MAGNOLIA, 280 CM
ZEBRA GLORIA BIO BO 2868 LIGHT BROWN, 280 CM